CPSD361 and CPRSD361 (Fire-rated)
Aesthetics
AtmoShield™ Powder Coating – It is a textured finish that combats the environments harsh wear and tear. This finish provides a thicker, more scratch resistant coat for added protection.
SpectraShield™ Powder Coating – It is a Polyester finish in more than 180 colors offering durability, aesthetics, superior finish life and cost effectiveness.
Safety & Protection
The StormDefender is designed specifically with life safety in mind for safe room protection against tornadoes and hurricanes. It has been tested and certified to ICC 500-2020 and FEMA P-361, Third Edition code standards.
LED Light Kit – Provides a high-visible status indication for rolling doors and grilles.
Sensing Edge – Designed with a flexible black rubber TPE material, our sensing edge has two fins that form to variations in the floor on both the interior and exterior of your door or grille. This ensures a secure seal without requiring you to over set the bottom door limit. On-the-go Sensing Edge Repair Kit now available. Contact the Service Department at 1-800-390-8590.
Usage
Designed specifically with life safety in mind for safe room protection against tornadoes and hurricanes.
Sizes
The minimum size is 3’ x 3’ and the maximum size is 14’ x 16’. The maximum width will vary between 13’10” and 14’ depending on the configuration. Please contact the factory if the maximum width is more than 13’10” to ensure the proper configuration.
Listings
Tested and certified to ICC 500-2020 and FEMA P-361, fourth edition code standards.
Standard Materials and Finishes
Curtain – 12 gauge 4” face flat Steel slat with SpectraShield® powder coat in gray.
Guides – Steel with powder coating to match the curtain.
Bottom Bar – 12 gauge 4” face steel bottom bar with powder coat to match the curtain.
No installation or care items available.
| Model | Section Thickness | Panel Design | Ext. Steel Gauge | Backer | R-value* | Max Width** | Max Height |
| 520 | 2″ | Ribbed Steel | 20 Gauge | N/A | N/A | 26’2″ | 20’0″ |
| 520S | 2″ | Minor & Deep Ribs | 20 Gauge | Pre-painted 30 gauge steel back cover | 6.6 | 26’2″ | 20’0″ |
| 522 | 2″ | Flush | 20 Gauge | N/A | N/A | 24’2″ | 24’0″ |
| 522S | 2″ | Flush | 20 Gauge | Pre-painted 30 gauge steel back cover | 6.6** | 24’2″ | 24’0″ |
| 524 | 2″ | Ribbed Steel | 24 Gauge | N/A | N/A | 24’2″ | 20’0″ |
| 524V | 2″ | Minor & Deep Ribs | 24 Gauge | Polyethylene vinyl back cover | 6.6 | 26’2″ | 20’0″ |
| 524S | 2″ | Minor & Deep Ribs | 24 Gauge | Pre-painted 30 gauge steel back cover | 6.6 | 24’2″ | 20’0″ |
| 525 | 2″ | Ribbed Steel | 25 Gauge | N/A | N/A | 20’2″ | 16’0″ |
| 525V | 2″ | Minor & Deep Ribs | 25 Gauge | Polyethylene vinyl back cover | 6.6 | 20’2″ | 16’0″ |
| 525S | 2″ | Minor & Deep Ribs | 25 Gauge | Pre-painted 25 gauge steel back cover | 6.6 | 20’2″ | 16’0″ |
| 664 | 2 1/8″ | Raised Panel Steel | 24 Gauge | N/A | N/A | 20’2″ | 16’0″ |
| 664V | 2 1/8″ | Raised Panel | 24 Gauge | Polyethylene vinyl back cover | 6.3 | 20’2″ | 16’0″ |
*Calculated door section R-value is in accordance with DASMA TDS-163
Insulated and Non-insulated doors come with a variety of options to address your building requirements. Options below are not available on all models. See model specific literature or consult a Clopay commercial dealer for option availability.
DESIGN OPTIONS:
- Windows
- 24″x6″
- 24″x12″
- Full View (pre-painted white or brown or clear anodized)
- Black frame Window with Rounded Corners
COLORS:
- White – All Models
- Brown – All Models
- Tan – 524, 524S, 524V
- Gray – 524, 524S, 524V
- Trinar White – 524, 524V, 525S
- Desert Tan – 664, 664V
- Sandtone – 664, 664V
- Almond – 664, 664V
PERFORMANCE OPTIONS:
- High Cycle Springs (25K, 50K and 100K available)
- 3″ heavy duty track (where not standard)
- Outside keyed Security Lock
- Double End Stiles
- Design pressure rated (WindCode)
- Impact Rated
- Photo eyes, sensing edges and Operators
- Extended 8-Year Hardware Warranty
- Header (top) and Jamb Seals
- High Performance Hardware Upgrade
CUSTOM OPTIONS:
- Mullions
- Breakaway Sections
- Pass Door
MODEL – 520/524/525
| Panel Design: | 2″ thick roll formed ribbed steel |
| Steel Gauge: | 20 ga (.034″ min) – Model 520, 24 ga (.022″ min) – Model 524and 25 ga (.019 min) – Model 525 ribbed steel sections |
| Joint Design: | Tongue and groove |
| Thickness/Insulation: | No insulation |
| Hardware: | 14 gauge hinges, commerical 10-ball steel rollers, 10,000 cycle torsion springs |
| Colors: | Pre-painted white or brown (520/525) Pre-painted white, brown, tan or gray (524) |
| Limited Warranty: | 10-year finish against rust / one-year material & workmanship |
MODEL 520S
| Panel Design: | 2″ thick roll formed stucco embossed ribbed steel |
| Steel Gauge: | 20 gauge (.034″ min) for maximum dent resistance |
| Joint Design: | Tongue and groove |
| Thickness /Insulation | 1-3/8″ thick polystyrene insulation with pre-painted 30 gauge steel backcover |
| Thermal Conductivity | R-Value 6.6* |
| Paint System: | 3-stage paint process delivers maintenance free finish that resists rust perforation |
| Colors | Pre-painted white or brown |
| Limited Warranty: | 10-year paint / one-year material & workmanship |
MODEL 524V / 524S
| Panel Design: | 2″ thick roll formed stucco embossed steel |
| Steel Gauge: | 24 gauge (.022″ min) ribbed steel sections |
| Joint Design: | Tongue and groove |
| Thickness /Insulation | 1-3/8″ thick polystyrene insulation with polyethylene vinyl backcover (524V) 1-3/8″ thick polystyrene insulation with pre-painted 30 gauge steel backcover (524S) |
| Thermal Conductivity | R-Value 6.6* |
| Paint System: | 3-stage paint process delivers maintenance free finish that resists rust perforation |
| Colors | Pre-painted white, brown, tan or gray |
| Limited Warranty: | 10-year paint /one-year material & workmanship |
MODEL 525V / 525S
| Panel Design: | 2″ thick roll formed smooth steel with combination of deep minor ribs |
| Steel Gauge: | 25 gauge (.019″ min) |
| Joint Design: | Tongue and groove |
| Thickness /Insulation | 1-3/8″ thick polystyrene insulation with polyethylene vinyl backcover (525V) 1-3/8″ thick polystyrene insulation with pre-painted 30 gauge steel backcover (525S) |
| Thermal Conductivity: | R-Value 6.6* |
| Paint System: | 3-stage paint process delivers maintenance free finish that resists rust perforation |
| Colors: | Pre-painted white or brown |
| Limited Warranty: | 10-year paint / one-year material & workmanship |
MODEL – 664
| Panel Design: | 1 7/8″ thick roll formed steel |
| Steel Gauge: | 24 gauge (.22″ min) raised panel door |
| Joint Design: | Tongue and groove |
| Thickness & Insulation | No insulation |
| Hardware: | 14 gauge hinges, commerical 10-ball steel rollers, 10,000 cycle torsion springs |
| Colors: | Pre-painted snowmist white, chocolate, brown, almond, sandstone, or desert tan. |
| Limited Warranty: | 10-year finish against rust through / one-year material & workmanship |
MODEL 664V
| Panel Design: | 1-7/8″ thick woodgrain embossed raised panel steel |
| Steel Gauge: | 24 gauge (.022″ min) ribbed steel sections |
| Joint Design: | Tongue-and-groove |
| Thickness /Insulation | 1-3/8″ thick polystyrene insulation with polyethylene vinyl backcover |
| Thermal Conductivity | R-Value 6.3* |
| Paint System | 3-stage paint process delivers maintenance free finish that resists rust perforation |
| Colors | Pre-painted white, brown, tan or gray; Trinar white or beige |
| Limited Warranty: | 10-year paint / one-year material & workmanship |
*Calculated garage door section R-value is in accordance with DASMA TDS-163.
COMMERCIAL HARDWARE
Commercial doors are designed with hardware to meet demanding applications of commercial building usage. All commercial doors are provided with the following hardware as standard. For additional upgraded hardware see “Options” tab.
- 14 gauge hinges
- Commercial 10 ball steel rollers with options for nylon tire rollers
- 10,000 cycle torsion springs
- Steel step plate and lift handle for easy operation
- Inside slide lock for increase security
- 19 gauge steel hinge support plates
- 18-gauge single end stiles; 16-gauge double end stiles
- Galvanized aircraft cables with 7:1 safety factory
- 2” or 3” track in a variety of configurations to meet building design requirements
COMMERCIAL TRACK APPLICATIONS
In commercial settings, space utilization and space constraints are important factors in choosing the correct hardware configuration for your application. Clopay track offerings and options enable you to make the most efficient use of available space. Options include standard lift, low head room front or rear mount, follow the roof pitch, full vertical or combination of these options.
COMMERCIAL TORSION SPRINGS
Designed to counterbalance even the largest doors, commercial torsion spring assemblies can be designed for Industry standard 10,000 cycles or can be upgraded to 25,000, 50,000 or 100,000 expected life cycles.