Industrial Gear – Head Operators
Technical Specifications
| Model | MGR 33/MGH 33 | MGR 50/MGH 50 | MGR 75/MGH 75 |
|---|---|---|---|
| Horsepower | 1/3 HP | 1/2 HP | 3/4 HP |
| Voltage | 115V/230V, 460V, 575V | 115V/230V, 460V, 575V | 115V/230V, 460V, 575V |
| Phase | 1 & 3 | 1 & 3 | 1 & 3 |
| Frequency | 50 Hz* / 60 Hz | 50 Hz* / 60 Hz | 50 Hz* / 60 Hz |
| Duty | 20 cycles/hr** | 20 cycles/hr** | 20 cycles/hr** |
| Drive Chain | #50 | #50 | #50 |
| Internal Lock Sensor | Optional (MGRL 33) / Optional (MGHL 33) | Optional (MGRL 50) / Optional (MGHL 50) | Optional (MGRL 75) / Optional (MGHL 75) |
| Auxiliary Hand Chain | Not Provided(MGRL 33) / Included (MGHL 33) | Not Provided(MGRL 50) / Included (MGHL 50) | Not Provided(MGRL 75) / Included (MGHL 75) |
Above products are protected by patent #6,900,602 #11,446,561 and #7,055,283. Other patents pending.
*Additional lead time may apply. Please contact factory for details.
**Medium-Duty Operator – tested to perform for up to 20 cycles in one hour, not to be used for consecutive hours. If consecutive hours or continuous duty is required, refer to the SG Super-Duty Operator.
- Module for secondary monitored entrapment protection device
- Programmable timer to closer
- Gear-Head construction at the price of a belt-drive operator
- Compact operator/mounting configuration is ideal for coiling doors – operators always fit within the coil height dimension
- Consistent mounting, appearance and wiring – across full line of operator models
- Considerably lighter weight than competitive belt-drive and gear-head operator models
- Auxiliary chain for emergency operation, just pull to operate
- UL listed
- Cycle counter
- Terminal connection for a monitored entrapment protection device
- 24 VDC warning output signal when the door is moving
- On board Open/Close/Stop buttons
- Close override if the entrapment protection device short circuits
No product brochures available.
No installation or care items available.
| Model | Section Thickness | Panel Design | Ext. Steel Gauge | Backer | R-value* | Max Width** | Max Height |
| 520 | 2″ | Ribbed Steel | 20 Gauge | N/A | N/A | 26’2″ | 20’0″ |
| 520S | 2″ | Minor & Deep Ribs | 20 Gauge | Pre-painted 30 gauge steel back cover | 6.6 | 26’2″ | 20’0″ |
| 522 | 2″ | Flush | 20 Gauge | N/A | N/A | 24’2″ | 24’0″ |
| 522S | 2″ | Flush | 20 Gauge | Pre-painted 30 gauge steel back cover | 6.6** | 24’2″ | 24’0″ |
| 524 | 2″ | Ribbed Steel | 24 Gauge | N/A | N/A | 24’2″ | 20’0″ |
| 524V | 2″ | Minor & Deep Ribs | 24 Gauge | Polyethylene vinyl back cover | 6.6 | 26’2″ | 20’0″ |
| 524S | 2″ | Minor & Deep Ribs | 24 Gauge | Pre-painted 30 gauge steel back cover | 6.6 | 24’2″ | 20’0″ |
| 525 | 2″ | Ribbed Steel | 25 Gauge | N/A | N/A | 20’2″ | 16’0″ |
| 525V | 2″ | Minor & Deep Ribs | 25 Gauge | Polyethylene vinyl back cover | 6.6 | 20’2″ | 16’0″ |
| 525S | 2″ | Minor & Deep Ribs | 25 Gauge | Pre-painted 25 gauge steel back cover | 6.6 | 20’2″ | 16’0″ |
| 664 | 2 1/8″ | Raised Panel Steel | 24 Gauge | N/A | N/A | 20’2″ | 16’0″ |
| 664V | 2 1/8″ | Raised Panel | 24 Gauge | Polyethylene vinyl back cover | 6.3 | 20’2″ | 16’0″ |
*Calculated door section R-value is in accordance with DASMA TDS-163
Insulated and Non-insulated doors come with a variety of options to address your building requirements. Options below are not available on all models. See model specific literature or consult a Clopay commercial dealer for option availability.
DESIGN OPTIONS:
- Windows
- 24″x6″
- 24″x12″
- Full View (pre-painted white or brown or clear anodized)
- Black frame Window with Rounded Corners
COLORS:
- White – All Models
- Brown – All Models
- Tan – 524, 524S, 524V
- Gray – 524, 524S, 524V
- Trinar White – 524, 524V, 525S
- Desert Tan – 664, 664V
- Sandtone – 664, 664V
- Almond – 664, 664V
PERFORMANCE OPTIONS:
- High Cycle Springs (25K, 50K and 100K available)
- 3″ heavy duty track (where not standard)
- Outside keyed Security Lock
- Double End Stiles
- Design pressure rated (WindCode)
- Impact Rated
- Photo eyes, sensing edges and Operators
- Extended 8-Year Hardware Warranty
- Header (top) and Jamb Seals
- High Performance Hardware Upgrade
CUSTOM OPTIONS:
- Mullions
- Breakaway Sections
- Pass Door
MODEL – 520/524/525
| Panel Design: | 2″ thick roll formed ribbed steel |
| Steel Gauge: | 20 ga (.034″ min) – Model 520, 24 ga (.022″ min) – Model 524and 25 ga (.019 min) – Model 525 ribbed steel sections |
| Joint Design: | Tongue and groove |
| Thickness/Insulation: | No insulation |
| Hardware: | 14 gauge hinges, commerical 10-ball steel rollers, 10,000 cycle torsion springs |
| Colors: | Pre-painted white or brown (520/525) Pre-painted white, brown, tan or gray (524) |
| Limited Warranty: | 10-year finish against rust / one-year material & workmanship |
MODEL 520S
| Panel Design: | 2″ thick roll formed stucco embossed ribbed steel |
| Steel Gauge: | 20 gauge (.034″ min) for maximum dent resistance |
| Joint Design: | Tongue and groove |
| Thickness /Insulation | 1-3/8″ thick polystyrene insulation with pre-painted 30 gauge steel backcover |
| Thermal Conductivity | R-Value 6.6* |
| Paint System: | 3-stage paint process delivers maintenance free finish that resists rust perforation |
| Colors | Pre-painted white or brown |
| Limited Warranty: | 10-year paint / one-year material & workmanship |
MODEL 524V / 524S
| Panel Design: | 2″ thick roll formed stucco embossed steel |
| Steel Gauge: | 24 gauge (.022″ min) ribbed steel sections |
| Joint Design: | Tongue and groove |
| Thickness /Insulation | 1-3/8″ thick polystyrene insulation with polyethylene vinyl backcover (524V) 1-3/8″ thick polystyrene insulation with pre-painted 30 gauge steel backcover (524S) |
| Thermal Conductivity | R-Value 6.6* |
| Paint System: | 3-stage paint process delivers maintenance free finish that resists rust perforation |
| Colors | Pre-painted white, brown, tan or gray |
| Limited Warranty: | 10-year paint /one-year material & workmanship |
MODEL 525V / 525S
| Panel Design: | 2″ thick roll formed smooth steel with combination of deep minor ribs |
| Steel Gauge: | 25 gauge (.019″ min) |
| Joint Design: | Tongue and groove |
| Thickness /Insulation | 1-3/8″ thick polystyrene insulation with polyethylene vinyl backcover (525V) 1-3/8″ thick polystyrene insulation with pre-painted 30 gauge steel backcover (525S) |
| Thermal Conductivity: | R-Value 6.6* |
| Paint System: | 3-stage paint process delivers maintenance free finish that resists rust perforation |
| Colors: | Pre-painted white or brown |
| Limited Warranty: | 10-year paint / one-year material & workmanship |
MODEL – 664
| Panel Design: | 1 7/8″ thick roll formed steel |
| Steel Gauge: | 24 gauge (.22″ min) raised panel door |
| Joint Design: | Tongue and groove |
| Thickness & Insulation | No insulation |
| Hardware: | 14 gauge hinges, commerical 10-ball steel rollers, 10,000 cycle torsion springs |
| Colors: | Pre-painted snowmist white, chocolate, brown, almond, sandstone, or desert tan. |
| Limited Warranty: | 10-year finish against rust through / one-year material & workmanship |
MODEL 664V
| Panel Design: | 1-7/8″ thick woodgrain embossed raised panel steel |
| Steel Gauge: | 24 gauge (.022″ min) ribbed steel sections |
| Joint Design: | Tongue-and-groove |
| Thickness /Insulation | 1-3/8″ thick polystyrene insulation with polyethylene vinyl backcover |
| Thermal Conductivity | R-Value 6.3* |
| Paint System | 3-stage paint process delivers maintenance free finish that resists rust perforation |
| Colors | Pre-painted white, brown, tan or gray; Trinar white or beige |
| Limited Warranty: | 10-year paint / one-year material & workmanship |
*Calculated garage door section R-value is in accordance with DASMA TDS-163.
COMMERCIAL HARDWARE
Commercial doors are designed with hardware to meet demanding applications of commercial building usage. All commercial doors are provided with the following hardware as standard. For additional upgraded hardware see “Options” tab.
- 14 gauge hinges
- Commercial 10 ball steel rollers with options for nylon tire rollers
- 10,000 cycle torsion springs
- Steel step plate and lift handle for easy operation
- Inside slide lock for increase security
- 19 gauge steel hinge support plates
- 18-gauge single end stiles; 16-gauge double end stiles
- Galvanized aircraft cables with 7:1 safety factory
- 2” or 3” track in a variety of configurations to meet building design requirements
COMMERCIAL TRACK APPLICATIONS
In commercial settings, space utilization and space constraints are important factors in choosing the correct hardware configuration for your application. Clopay track offerings and options enable you to make the most efficient use of available space. Options include standard lift, low head room front or rear mount, follow the roof pitch, full vertical or combination of these options.
COMMERCIAL TORSION SPRINGS
Designed to counterbalance even the largest doors, commercial torsion spring assemblies can be designed for Industry standard 10,000 cycles or can be upgraded to 25,000, 50,000 or 100,000 expected life cycles.